MCX Connector Male Solder UT047 Cable Type 50ohm – RHT-617-1011

Broadband performance with low reflection
High-quality solution at a low cost
Quick connect/disconnect snap-on mating reduces installation time
Conforms to European CECC 22000 specifications
Available in straight and right-angle plugs and printed circuit board connectors

The connector was developed in Europe from the 1980s to the 1990s. It adopts a push-in coupling method and is suitable for quick insertion and removal. Ultra-micro size, small size, lightweight, compact structure, widely used in small communication equipment with space constraints.

MCX connectors are approximately 30% smaller than SMB connectors, are available in both 50 and 75 Ohm versions, and provide good electrical performance to 6 GHz.

Mainly applicable to aerospace and defense, medical, commercial vehicles, telecommunications, data/communications, industrial, etc.

MCX Connector

MMCX Connector

Interface

Application Scenarios

Product Specification

RF Series	MCX Type
Connector Type	Plug
Orientation	Right Angle
Contact Type	Male Pin
Contact Termination Style	Solder
Shield Termination	Solder
Mounting Type	Cable Mount
Cable Type	UT047
Fastening Type	Push-Pull
Number of Ports	1
Impedance	50 ohm
Frequency - Max	6GHz
Shell Material	Copper Alloy
Shell Finish	Gold Plated
Insulator Material	Teflon White
Contact Material	Brass
Contact Finish	Gold Plated
Rated Voltage	500 Volts RMS Max Continuous
Dielectric Withstanding Voltage	1000 VRMS Max
Insultation Resistance	500 MΩ Min
Center Contact Resistance	5 MΩ Min
Outer Contact Resistance	1 MΩ Min
Temperature Range	-65℃ to +165℃
Mating Durability	≥ 500 Cycles
VSWR	≤1.15 (DC to 4 GHz), ≤1.40 (4 to 6 GHz)
Vibration	MIL-STD-202 Meth. 204
Corrosion Resistance	MIL-STD-202 Meth. 101
RF Series	MCX Type	Connector Type	Plug
Orientation	Right Angle	Contact Type	Male Pin
Contact Termination Style	Solder	Shield Termination	Solder
Mounting Type	Cable Mount	Cable Type	UT047
Fastening Type	Push-Pull	Number of Ports	1
Impedance	50 ohm	Frequency - Max	6GHz
Shell Material	Copper Alloy	Shell Finish	Gold Plated
Insulator Material	Teflon White	Contact Material	Brass
Contact Finish	Gold Plated	Rated Voltage	500 Volts RMS Max Continuous
Dielectric Withstanding Voltage	1000 VRMS Max	Insultation Resistance	500 MΩ Min
Center Contact Resistance	5 MΩ Min	Outer Contact Resistance	1 MΩ Min
Temperature Range	-65℃ to +165℃	Mating Durability	≥ 500 Cycles
VSWR	≤1.15 (DC to 4 GHz), ≤1.40 (4 to 6 GHz)	Vibration	MIL-STD-202 Meth. 204
Corrosion Resistance	MIL-STD-202 Meth. 101

RF Series	MCX Type
Connector Type	Plug
Orientation	Right Angle
Contact Type	Male Pin
Contact Termination Style	Solder
Shield Termination	Solder
Mounting Type	Cable Mount
Cable Type	UT047
Fastening Type	Push-Pull
Number of Ports	1
Impedance	50 ohm
Frequency - Max	6GHz
Shell Material	Copper Alloy
Shell Finish	Gold Plated
Insulator Material	Teflon White
Contact Material	Brass
Contact Finish	Gold Plated
Rated Voltage	500 Volts RMS Max Continuous
Dielectric Withstanding Voltage	1000 VRMS Max
Insultation Resistance	500 MΩ Min
Center Contact Resistance	5 MΩ Min
Outer Contact Resistance	1 MΩ Min
Temperature Range	-65℃ to +165℃
Mating Durability	≥ 500 Cycles
VSWR	≤1.15 (DC to 4 GHz), ≤1.40 (4 to 6 GHz)
Vibration	MIL-STD-202 Meth. 204
Corrosion Resistance	MIL-STD-202 Meth. 101

Renhotec Information

Where is your factory located? Can I visit your factory?

We have two factories, one is located in Dongguan city, another in Jiangmen city. Visitors are always welcome.

RF Connector Selection

What factors should I consider when choosing an RF connector?

Factors to consider include frequency range, impedance, insertion loss, durability, mating cycle, and environmental conditions. These factors are important to ensure optimal performance of Renhotec RF connectors.

Customization and Sample Testing

Can Renhotec customize products for us?

Yes, we offer customization services to meet your specific needs. Please provide your specification, performance requirement or drawing, photos, or samples for evaluation.

Can you provide samples for testing?

Absolutely, Renhotec provides samples for testing before proceeding with a bulk order.

Order Lead Time

What is the lead time and availability of these connectors?

Lead time depends on the product type, quantity, and production status. For items ready in stock, the lead time is 3-5 working days. For common items, the lead time for 10K is 10-12 working days. The accurate lead time can be provided once the order is confirmed.