MCX Connector Jack Solder Panel Mount Through Hole 50ohm – RHT-617-1029

Broadband performance with low reflection
High-quality solution at a low cost
Quick connect/disconnect snap-on mating reduces installation time
Conforms to European CECC 22000 specifications
Available in straight and right-angle plugs and printed circuit board connectors

The connector was developed in Europe from the 1980s to the 1990s. It adopts a push-in coupling method and is suitable for quick insertion and removal. Ultra-micro size, small size, lightweight, compact structure, widely used in small communication equipment with space constraints.

MCX connectors are approximately 30% smaller than SMB connectors, are available in both 50 and 75 Ohm versions, and provide good electrical performance to 6 GHz.

Mainly applicable to aerospace and defense, medical, commercial vehicles, telecommunications, data/communications, industrial, etc.

MCX Connector

MMCX Connector

Interface

Application Scenarios

Product Specification

RF Series	MCX Type
Connector Type	Jack
Orientation	Right Angle
Contact Type	Female Pin
Contact Termination Style	Solder
Shield Termination	Solder
Mounting Type	Panel Mount
Mounting Feature	Through Hole
Fastening Type	Push-Pull
Number of Ports	1
Impedance	50 ohm
Frequency - Max	6GHz
Shell Material	Copper Alloy
Shell Finish	Gold Plated
Insulator Material	Teflon White
Contact Material	Brass
Contact Finish	Gold Plated
Rated Voltage	500 Volts RMS Max Continuous
Dielectric Withstanding Voltage	1000 VRMS Max
Insultation Resistance	500 MΩ Min
Center Contact Resistance	5 MΩ Min
Outer Contact Resistance	1 MΩ Min
Temperature Range	-65℃ to +165℃
Mating Durability	≥ 500 Cycles
VSWR	≤1.15 (DC to 4 GHz), ≤1.40 (4 to 6 GHz)
Vibration	MIL-STD-202 Meth. 204
Corrosion Resistance	MIL-STD-202 Meth. 101
RF Series	MCX Type	Connector Type	Jack
Orientation	Right Angle	Contact Type	Female Pin
Contact Termination Style	Solder	Shield Termination	Solder
Mounting Type	Panel Mount	Mounting Feature	Through Hole
Fastening Type	Push-Pull	Number of Ports	1
Impedance	50 ohm	Frequency - Max	6GHz
Shell Material	Copper Alloy	Shell Finish	Gold Plated
Insulator Material	Teflon White	Contact Material	Brass
Contact Finish	Gold Plated	Rated Voltage	500 Volts RMS Max Continuous
Dielectric Withstanding Voltage	1000 VRMS Max	Insultation Resistance	500 MΩ Min
Center Contact Resistance	5 MΩ Min	Outer Contact Resistance	1 MΩ Min
Temperature Range	-65℃ to +165℃	Mating Durability	≥ 500 Cycles
VSWR	≤1.15 (DC to 4 GHz), ≤1.40 (4 to 6 GHz)	Vibration	MIL-STD-202 Meth. 204
Corrosion Resistance	MIL-STD-202 Meth. 101

RF Series	MCX Type
Connector Type	Jack
Orientation	Right Angle
Contact Type	Female Pin
Contact Termination Style	Solder
Shield Termination	Solder
Mounting Type	Panel Mount
Mounting Feature	Through Hole
Fastening Type	Push-Pull
Number of Ports	1
Impedance	50 ohm
Frequency - Max	6GHz
Shell Material	Copper Alloy
Shell Finish	Gold Plated
Insulator Material	Teflon White
Contact Material	Brass
Contact Finish	Gold Plated
Rated Voltage	500 Volts RMS Max Continuous
Dielectric Withstanding Voltage	1000 VRMS Max
Insultation Resistance	500 MΩ Min
Center Contact Resistance	5 MΩ Min
Outer Contact Resistance	1 MΩ Min
Temperature Range	-65℃ to +165℃
Mating Durability	≥ 500 Cycles
VSWR	≤1.15 (DC to 4 GHz), ≤1.40 (4 to 6 GHz)
Vibration	MIL-STD-202 Meth. 204
Corrosion Resistance	MIL-STD-202 Meth. 101

Renhotec Information

Where is your factory located? Can I visit your factory?

We have two factories, one is located in Dongguan city, another in Jiangmen city. Visitors are always welcome.

RF Connector Compatibility

Does the connector comply with international standards and is it interchangeable with similar products of other brands?

Yes, our RF connector interface dimension conform international standards. Normally it’s interchangeable with similar products of other brands, it’s better to send us the datasheet/sample of other brands for check before order.

Is this RF connector suitable for the PCB of our device?

We recommend that you provide us with detailed specifications of your existing interfaces and cables, performance requirement and usage environment, so that our technical team can evaluate them.

Will this RF connector fit well with my existing connector interfaces and cables?

Please advise your PCB layout dimension requirement, we’ll recommend you the most suitable Renhotec drawing for check.

Customization and Sample Testing

Can Renhotec customize high frequency RF connector? Such as SMA 0-18G.

Yes, we offer customization services to meet your specific needs. Please provide your specification, performance requirement or drawing, photos, or samples for evaluation.

For RF PCB connector, can center pin dimension be customized according to my requirement?

Yes, we provide customised services, it has MOQ requirement, please send your requirement for our engineer team evaluation.

Is the thread length can be customized? Such as SMA connector thread length.

Yes, please advise the thread length for evaluation.

Can you assembly cable base on our requirement?

Yes, we can. Please send us the datasheet or connector and cable requirement, we can produce as per request.

Can you customize according to my datasheet/drawing?

Yes, please share it and the requirement with us, our engineer team will evaluate it.

RF Connector Specifications

What's the impedance of RF connector?

The impedance of an RF connector typically refers to the characteristic impedance of the transmission line it supports. The most common characteristic impedances for RF connectors are 50 ohms and 75 ohms. Please select an RF connector with the appropriate characteristic impedance to ensure optimal signal transmission and minimal signal loss within the system.

Order Lead Time

What is the lead time and availability of these connectors?

Lead time depends on the product type, quantity, and production status. For items ready in stock, the lead time is 3-5 working days. For common items, the lead time for 10K is 10-12 working days. The accurate lead time can be provided once the order is confirmed.